Conel CDA 70 Spezifikationen

Declared system ISO 9001:2009 [email protected]

CDA70 MODEM DESCRIPTION 10 2.5.1. Connection of PORT1, PORT2 and PORT3 connectors (RS232) (RS232 – DCE – Data Communication Equipment) Pin numb

CDA70 MODEM DESCRIPTION 11 Circuit example of the RS232 equipment with modem CDA70: 2.5.2. Connection of PORT1 connectors (M-BUS) Panel socket R

CDA70 MODEM DESCRIPTION 12 Circuit example of the meter with modem CDA70 with data cable length more than 10 m: M-BUS data cable more than 10 m

CDA70 MODEM DESCRIPTION 13 Circuit example of the meter with modem CDA70 with data length less than 10 m: Circuit example of the meter with mo

CDA70 MODEM DESCRIPTION 14 2.5.4. Connection of ETH connectors (ETHERNET) Panel socket RJ45 Pin number Signal mark Description Data flow directi

CDA70 MODEM DESCRIPTION 15

CDA70 MODEM DESCRIPTION 16 2.5.6. Power supply connector (PWDD) Pin number Signal mark Description 1 +12V Positive pole of supply voltage 2

CDA70 MODEM DESCRIPTION 17 Circuit example: DC supply DC supply with backup battery with present supply monitoring DC supply with backup ba

CDA70 MODEM DESCRIPTION 18 2.6. Antenna connection Antenna is connected to the radio data modem via a BNC connector located on the side panel. 2

CDA70 MODEM DESCRIPTION 19 2.8. Ports technical specifications • RS232 Name of product RS232 Power supply Internal ... Environment Operatin

CONTENTS 2 Contents 1. Safety instructions 4 2. Description of the CDA70 radio modem 5 2.1. General 5 2.2. Examples of possible applications

CDA70 MODEM DESCRIPTION 20 Connection of the jumpers: • M-BUS Name of port M-BUS Power supply Voltage 10,8 .. 15,6 V Supply power Max. 30 W

CDA70 MODEM DESCRIPTION 21 Connection of the jumpers: • Ethernet Port ETHPower supply Internal ... Environment Operating temperature -

CDA70 MODEM DESCRIPTION 22 2.9. Configuration of radio modem The Radwin configuration program [1] has been designed to set up the CDA70 radio da

CDA70 MODEM DESCRIPTION 23 2.11. Accessories 1. Power supply connector for a power supply cable 2. Three RJ45 connectors to complete the data c

CDA70 MODEM DESCRIPTION 24 2.13. Mechanical drawing of CDA70 and recommendations for montage For the majority of applications with a built-in m

CDA70 MODEM DESCRIPTION 25 For compliance of EN 60439 - 1 + A1 specification it is necessary observe next assembly of the modem to the switch - b

CDA70 MODEM DESCRIPTION 26 • sufficient space must be left before individual connectors for handling of cables, • for correct function of the

CDA70 MODEM DESCRIPTION 27 2.14. Product marking Marking Antenna connector Power supply Other CDA-70-XX-YY BNC +10,8 to 15,6 V DC CIO XX – f

CDA70 MODEM DESCRIPTION 28 2.15. Assembly procedure The radio data modem CDA70 is designed as a standard for: 1. DIN 35 mm rail assembly using p

CDA70 MODEM DESCRIPTION 29 2. DIN 35 mm rail assembly using plastic grips from back side.

CONTENTS 3 5.1. Systems 39 5.2. Protocols 39 5.3. Software 39 5.4. Products 39 6. Product disposal informations 39 7. Complaints procedure

CDA70 MODEM DESCRIPTION 30 2.16. Product label

CDA70 MODEM DESCRIPTION 31 2.17. Basic parameters description For monitoring of status, configuration and administration of the modem is RADWIN p

CDA70 MODEM DESCRIPTION 32 Parameter name Set value range Parameter description RF channel protocol --- Information about used radio channel pro

CDA70 MODEM DESCRIPTION 33 Parameter name Set value range Parameter description Low threshold RF signal level -90 up to -130 dBm Threshold of RF

CDA70 MODEM DESCRIPTION 34 Parameter name Set value range Parameter description Log CIO YES/NO When this parameter is set to YES, than CIO infor

CIO DESCRIPTION 35 3. CIO - analogue inputs and binary outputs 3.1. Introduction CDA70 is equipped with a user interface (I/O) for scanning and p

CIO DESCRIPTION 36 3.2.4. I/O signals parameters Signal name Measuring range [V] Resolution [bit] Sampling [msec] Average from samples Hysteresis

CIO DESCRIPTION 37 3.3.3. Measuring DSR output signal level On CDA70 side, DSR signals on individual user interfaces are output signals. They are

CIO DESCRIPTION 38 LED on the front panel. Input circuits are protected against short-time over voltage by suppressors and against the long-time o

REFERENCE AND LINKS 39 4. Reference [1] Conel s.r.o.: RADWIN Program for control AGNES, 2008 [2] Conel s.r.o.: Application CGU Server, 2004 [3]

SAFETY INSTRUCTIONS 4 1. Safety instructions Please observe the following safety instructions: • The communication module has to be used in acco

COMPLAINTS PROCEDURE 40 7. Complaints procedure Dear customer, The product you have purchased had passed manufacturer's tests and its functio

COMPLAINTS PROCEDURE 41 3. The claim is deemed unsubstantiated when the defect is not found by the vendor processing the complaint or the defect

WARRANTY 42 8. Warranty Device type Serial number Guarantee period (months) Vendor Date of purchase Seal of the vendor

WARRANTY 43 1 2 3 4 5 Date of complaint registration Complaint protocol number Date of reception of the device

CDA70 MODEM DESCRIPTION 5 2. Description of the CDA70 radio modem 2.1. General The CDA70 radio modem is a device for wireless data transmission.

CDA70 MODEM DESCRIPTION 6 2.3.2. Modem component The modem part converts digital bit flow from the microcomputer to the FFSK or GMSK analogue mo

CDA70 MODEM DESCRIPTION 7 outputs. With the equipment you may establish simple telemetry at low cost, without the use of industrial control autom

CDA70 MODEM DESCRIPTION 8 2.3.6. Technical parameters Frequency band 143 – 174 MHz (CDA70V version) 403 – 470 MHz (CDA70U version) Adjustment o

CDA70 MODEM DESCRIPTION 9 2.4. Radio modem status indication Seven LED status indicators informing of the radio data modem status are located on